Business

4 Tips For Embroidery Hooping To Get Desired Results

The embroidery hoop helps in stabilizing the fabric. Also, it provides proper tension to the fabric over which you are going to create the embroidery design. The inadequate hooping can lead to the stretching of the garment, moving of fabric, bad stitches, and many more.

It is very difficult to master the skill of hooping. If the hooping is done appropriately, then it can help in producing the best embroidery results. If you want to create the design on the t-shirt, then you should take the help of the embroidery professionals like custom socks contractors. With the help of embroidery hooping, you can easily get aligned stitches and a pucker-free design.

1. Pick The Right Hoop

You should use the smallest hoop in which you can fit your design. If the edge of the hoop will be closer to the design, then it will lead to more stabilization of the fabric. The very small hoop can help in forming a beautiful design. If the size of the hoop is very large, then it may lead to the moving of fabric.

Ultimately, it will lead to puckering of design and your design will come out very poor. Not just the size, but the shape of the hoop also affects the embroidery design you create. The circular hoop can hold the material properly and efficiently.

2. Use T-pins With Large Size Hoops

If you want to secure the fabric in the large size rectangular hoop, then you should use T-pins. These pins will help in holding the fabric in its place. It is very important to note that this technique should be used on those stabilizers or fabrics which are not very much important for you. It is so because the t-pins can leave some holes and marks on them.  

If you want to implement this technique, you have to hoop the fabric in the normal way. Once you have achieved this, and then should use the T-pins to secure the position of the stabilizer or fabric in the right place. The T-pins will help in preventing any potential movement.

You should insert the T-pins at the place where the stabilizer or fabric touch each other between the two hoop frames after being hooped. It is imperative to insert the flush with the flame. Now, if the stabilizer or fabric starts pulling the loose areas of the frame, then T-pins will help to stop the movement.

It is recommended that you should insert the T-pins around the straight areas of hoops because their areas are not held strongly by the hoop. If you are not good at embroidery, then take the help of professionals like custom embroidery Calgary contractors.

3. Utilize Double Sided Tape

We recommend you use double-sided tape because it is one of the best techniques to keep the fabric at its place if you are dealing with sheer, stretchy, or slippery fabric. It is so because the stabilizer that touches the outer section of the hoop does its job properly.

It holds the plastic section of the outer hoop. Usually, the main cause of puckering is that the stabilizer is touching the inner section of the hoop does not offer a good grip. Thus, if you have one section which is holding properly and another part is slipping, then you will obtain a distorted and puckering design.

Therefore, we recommend you use double-sided tape to the outer side of the inner hoop, where material touches the hoop. It will help you to get rid of slipping between fabric and stabilizer. This technique will help you to obtain good results. The double side tape will work for various hooping until it will lose its sticky part.

After that, you should simply remove the tape and apply a new piece to it. Moreover, this trick will not leave any residue on the fabric. The ducted tape technique will also do the same job just like the T-pin technique. The ducted tape technique is not invasive to the fabric. The embroidery designs created by the apparel embroidery Calgary contractors are of top-notch quality.

4. Avoid Over Tightening Of Hoop

You should always keep in mind that you should not over-tighten your hoop due to aggressive adjustment of the knob when the fabric has been already hooped. Usually, the beginners, hoop the fabrics quite loosely. After that, you should aggressively turn the knob for the tightening of the hoop.

Sometimes, a finger-tight burn is needed. But we do not recommend you to take a screwdriver and tighten up the hoop to the maximum value. If you will use the screwdriver for the tightening of the hoop, then it will lead to the wastage of time, lead to fabric burn, and also it is harmful to the embroidery stitch out.

Rather than tightening the hoop by turning the knob, you should pull it gently. After that, you should pick up the hoop and slightly push the corners. You have to make it drum-tight so that you can put it inside the embroidery machine.  

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *